to the top of your throat plate.
Low Shank: Approximately ½”
Medium Shank: Approximately ¾”
High Shank: Approximately 1”
High Shank Straight Stitch: Machines without the ability to adjust the needle position. There are currently 3 different High Shank Straight Stitch feet for different straight stitch machines: Specify Juki TL2010Q, Brother PQ1500, or Janome MC1600P.
Fine Line® CLARITY Ruler Foot
See Where You Have Been; Know Where You Are Going!
Made with a strong polycarbonate material, visibility you can see around and throughout. You spend a lot of time marking your design elements on your quilt, now you can see where you are needing to go at all times. This foot can be used with straight or curved rulers, and both outside and inside areas of templates.
The Clarity ruler feet are currently available in four sizes. Consult chart below to find the size that fits your machine.
Does your machine have a high shank or low shank?
With your machine’s PRESSER FOOT LEVER down in its lowest position, and your needle down in its lowest position, measure from the middle of the screw hole to the top of your throat plate.
Low Shank: Approximately ½”
High Shank: Approximately 1”
(If your machine has a different height than the two listed above, you will need a different size foot.)
Please note Fine Line Clarity Slant Shank Foot is recommended for the Singer Vintage 301 and 301a only at this time.
- Straight Stitch machines will use the High Shank CRF-SS foot, such as some Juki, Brother, Janome 1600, etc.
Clarity ruler Foot, A Clear Option by Patsy Thompson.
Brief video introducing the Clarity Foot, a new ruler foot for sit down, push through quilting, made of clear acrylic by Accents in Design. Since it is clear you can easily see through it to see your markings and your stitching as you proceed. No more obstruction by metal ruler feet. This foot fits nearly all domestic machines and will be a great addition to your quilting arsenal!
SEE OUR RULER FOOT IN ACTION ...
Installation of the Clarity foot is simple. This video shows you how:
Check out this video by Jeanne Harrison demonstrating the new foot.
Sew More Videos on Clarity Ruler Foot
NOTICE: We stand behind our product, if there is any issue we will replace the product.
That being said the Clarity Foot is produced from polycarbonate material which is extremely strong.
We have sold literally thousands of the Clarity Feet. We have accounts all over the international stage, as well as a strong presence in the US. We have not had one Clarity Foot returned due to breakage. If it were an issue we would not have the Professional Quilter's endorsements that we do for our product.
Click Here to see the Longarm Ruler Foot
Made in USA
The Clarity ruler foot is very affordable in comparison to others on the market.
Made of high strength polycarbonate, the same material used for bullet-proof glass
FIND YOUR MACHINE... on our lookup chart to determine the right size foot for your machine >>>
The new Clarity Slant Shank ruler foot fits the following Singer Slant Shank machines: 1000 (Futura), 1036, 1100, 1411, 1425, Athena 2000 (2000A), 2001, 290, 301, 301A,4552, 4562, 4610, 4622, 500, 501, 502, 503, 503A, 5910, 5932, 600, 600E Touch & Sew, 603, 604, 611, 620E1, 6233, 6234, 6235, 625, 625E1, 625E6, 625E7, 626, 6267, 6268, 628, 629, 630, 631, 635, 636, 638, 639, 645, 646, 649, 6704, 6800 Series, 700, 7028, 7033, 714, 717 School, 719, 720, 724, 734, 737, 740, 750, 755, 756, 758, 760, 770, 774, 775, 776, 778, 8019, 9005, 9008, 9010, 9015, 9018, 9020, 9022, 9027, 9032, 9034, 9110, 9113, 9133, 9134, 9137, 9143, 920-3, 9210, 9217, 9224, 9240, 93220, 9323, 9334, 9408, 9410, 9416, 9420, 9423, 9430, 9432, 9444, 9417, 635E3, 635E6, 635E7, 900-3, 784, 786, 30920, 9440, 640 Touch & Sew, 6740, 9400, 9135, 9123, 9012, 1410, 1050 Futura, 6200, 6260, 266, 411, 610, 766, 729, 725, 721, 746, 708, 706, 431, 626E1, 626E6, 626E7.
I received my Clarity ruler foot which is specified for an HQ Sweet 16 long arm machine. After installing it, I checked it for proper alignment, and noticed it is off 1/16" from front to back. My machine needle is supposed to be perfectly centered in the foot. It measures exactly in the center from left to right, but it is 1/16" back too far when measuring front to back. Since there is no way to change the position of the needle, I tried to see if there was any wiggle room when attaching the ruler foot by screwing the hex screw with the Allen wrench, but there is no wiggle room. It is important for the needle to be centered in the foot when working with rulers. Do you have any thoughts for a solution for me?
Thanks for your time & attention.
The needle is centered in the foot perfectly. I also have a HQ Sixteen and when developing this foot in order to enhance the connective stability with the arc of the foot to the
ruler toe itself we had our engineer build up on the inside of the ruler toe. Ruler work is done on the outside of the foot not the inside. The ruler toe dia is 1/2" front to back and side to side. If she is measuring across the top of the ruler toe to the arc she is stopping at the enhancement, or she is indicating that from a visual which would look like the needle is closer to the back of the ruler toe than the front. Clarity.
Westalee WF-PKG Medium Shank Starter Kit Free Motion Quilting Ruler Foot +Arc for Bernina*
Westalee WF-PKG Low Shank Starter Kit Free Motion Quilting Ruler Foot +Arc & Feather Templates
Westalee Simple Ovals and Hexagons Template Ruler Choose Size Options/Pricing via drop menu